Tobee® TY series high temperature molten salt pump

1.Overview

Tobee® TY series high temperature molten salt pump also known as molten salt sump pump and high temperature sump pump, This type pump was designed after years of production of sump pump and on the basis of hightemperature molten salt pump, and Refer to the structure of the foreign same kind products,Developed hightemperature sump pumps.It is a ideal pump for transporting high temperature liquids,Especially for transporting high temperature molten salt.

TY series high temperature molten salt pump is a single stage,single suction,heat-resistant sump pump,The impeller is centrifugal type impeller.This pump has advantages of Easy to start, no leakage, smaller area etc.This pump adopt effective cooling type, reasonable structure and material,It is a special pump for transporting under 600 ℃ high temperature molten salt, high temperature oil and other high temperature liquids pump.

2.Performance range

Operating temperature （ T）： 180℃～800℃
Capacity（ Q）：3～400 m3/h
Head（ H）：5～125 m
Speeld（ n）： 980/1450/2860 r/min
Submerged depth（ L）： 0.6～8 m
Discharge diameter range：φ 25～φ 200mm

3.Range of application

TY Series High temperature molten pump apply to high temperature molten salt (a mixture of potassium
nitrate, sodium nitrite and sodium nitrate) or other high temperature medium,It is widely used in Melamine,
phthalic anhydride, maleic anhydride, acrylic acid, urea, refrigerant, alumina, and base oil and chemical industry
base project, Applied in the metal heat treatment and solar power generation project, at the same time also can be
used to transport high temperature heat conduction oil, acid, alkali and other corrosive liquids.

4.Structural features

    TY series high temperature molten salt pump is a vertical pump, mainly composed of pump body, pump cover, impeller, pump shaft, takeover, fluid tubes, bearing support, motor bracket, bracket, installation base plate,coupling, cooling water pipe, vertical machine, etc, can be found in the section.The detailed structure of the pump please consult Hebei Tobee Pump Co.,Limited

    Backplane hereafter called fluid, a portion of the pump installation when it insert in the molten salt tank
(tank), pump body, impeller, pump cover are immersed in molten salt below the liquid surface, through the impeller rotating pumping molten salt, pump shaft by supporting tube and installation base plate at the top of the bracket, bracket, motor bracket and connected.

    In a rolling bearing bracket, by the high temperature lubricating grease.On bearing bracket shell is equipped with cooling jacket, water cooling, in order to reduce the temperature of the grease in the bearing support.Bearing support the following stent lumen also have water cooling, to prevent liquid transmission part quantity of heat to the bearing support, reducing the bearing temperature.Due to the dual cooling to ensure the pump work normally at high temperature.

     Pump shaft is usually a long shaft, shaft above is rolling bearing, axis is below the metal sliding bearing.Pumping high temperature molten salt pump, submerged depth is longer than the pump shaft will consist of two or three segments, with rigid coupling between pick up into a long axis, and in the central axis with metal sliding bearing in the middle of the bearing.Pumping submerged depth of the molten salt pump is small, without intermediate bearing.

    The inlet of high temperature molten salt pump body, only the suction pipe are in the following fashion: when using the molten salt pump, when the liquid level to higher level open pump, draw the liquid surface to pump inlet side (lower level) to stop the pump, and waited to open pump on the liquid surface, at this moment if submerged depth is deeper, into the suction pipe can be under the same depth is relatively short pump shaft, the length of the supporting tube, fluid pipe, make the pump running smoothly, prolong service life, reduce the weight of molten salt pump, molten salt pump cost;If molten salt pump when used in any liquid level position to stop the pump or pump, cannot install thesuction pipe. 

    When submerged depth of the molten salt pump is longer, we call it a long axis of high temperature molten salt pump.Hebei Tobee Pump Co.,Limited with reliable joint shaft style and unique structure design, has solved the long axis of molten salt liquid pump pump shaft under lubrication and rigid problem, pump shaft by coupling connection, external connection casing, casing wall open hole, so that the medium into the sliding bearing.In the pump discharge a take over to the sliding bearing, when molten salt level dropped to below the sliding bearing,ensure that the sliding bearing lubrication.Long axis molten salt pump ensures the molten salt of molten salt tank entirely pumping light.

Sales Director/International dept.

HEBEI TOBEE PUMP CO.,LIMITED
Add:Hi-tech Development Zone | Shijiazhuang City | Hebei Province | China.

Email:Sales@tobeepump.com | Skype:Tobee.pump | Mob:+86-18731151301 | Web:www.tobee.cc