How to Select a Dredge Pump or Slurry Pump?
Dredge Pump or Slurry Pump Selection Introduction
Definition of Dredge Pump and Slurry Pump
Primary selection requirements for dredge pumps
Pump power rating:
The power consumption by the dredge pump is estimated from the discharge head, flow rate and specific gravity of pumped slurry. It is critical to verify that power rating of the selected pump is higher than the calculated power consumption after taking into account reasonable variations in operating conditions.
Material selection:
Typical material used for the construction of slurry pumps are cast iron, stainless steel, and high chrome steel. Some slurry pumps come with a lining to better deal with problems of slurry abrasion. A few elastomers which are used in the lining material are natural rubber, polyurethane or neoprene. The selection of lining material depends on the operating temperature, pH of slurry and the presence of specific abrasive fluids used in the dredging process.
Type of slurry pump installation:
Based on the shaft orientation, the slurry pumps can be divided as horizontal pumps and vertical pumps with horizontal pumps having the shaft in a horizontal position while the vertical pumps have a vertically aligned shaft.
Horizontal pumps are the most common types of slurry pumps used, and hence have the advantage of ease of installation or maintenance, a wide range of selection of flow parameters and choice of design materials. However, the vertical pumps among other benefits have the advantage of requiring relatively much lesser ground space for installation.
Another method to classify the type of installation for slurry pumps is dry installation or wet installation. Dry installation pumps have the hydraulic end and the drive located outside the liquid while the wet installation pumps such as submersible pumps operate inside the sump or the slurry. The submersible pumps do not require much support structure, hence, do not occupy much space. Depending on the kind of operation and installation desired the preferred method of pump installation is decided.
Specific problems faced in Dredge pump operation
Clogging:
Due to an extremely varied grain size distribution of materials handled by dredge pumps clogging of the suction or discharge of the pumps is a damaging phenomenon which leads to expensive maintenance procedures and more importantly high downtime. Our patented technology at Tobee pump has a high tolerance of sizes of materials handled, with a capacity to handle sizes as large as 9 inches. The open rotor design lets anything which can go through the inlet pass through the discharge without any setbacks.
Abrasion:
Massively abrasive nature of slurry’s solid particles causes an enormous amount of wear and tear in pumps. Due to the harsh environments in which slurry pumps operate, Tobee pump gives utmost importance to use the finest material for the impeller, seal, and casing to prolong the lifetime of the pump.
Conclusion:
Hopefully, you have a better understanding of the elements needed for proper pump selection. Even better is talking with us to help with your project specific needs.
At Tobee Pump we are committed to providing best-in-class dredge pumps to our customers; hence, each component is thoroughly tested to deliver supreme quality, reliability and versatility. Our unique technology provides us with an extraordinary capability to easily handle materials with enormous volumes and high specific gravity in tough conditions.
HEBEI TOBEE PUMP CO.,LIMITED
Add:Hi-tech Development Zone | Shijiazhuang City | Hebei Province | China.
Email:Sales@tobeepump.com | Skype:Tobee.pump | Mob:+86-18032034573 | Web:www.tobeepump.com
Dredge pump or slurry pump
selection could be a challenging process which could be simplified with
the understanding of the primary factors behind smooth pump operation.
Apart from delivering a more efficient performance, the right dredge
pump requires lesser maintenance, reduced power and has a relatively
longer life.
Slurry pump and dredge pump terms may be used interchangeably.
Slurry pump and dredge pump terms may be used interchangeably.
Definition of Dredge Pump and Slurry Pump
Slurry
pumps are the mechanical devices utilized for pressure-driven transport
of a fluid mixture (aka slurry). The fluid mixture by and large
consists of water as a liquid with solids being minerals, sand, gravel,
human waste, drilling mud or most of the crushed materials.
Dredge pumps are a special category of heavy duty slurry pumps that are utilized in the process of dredging. Dredging is referred to as the process of transport of underwater sediments (usually sand, gravel or rocks) from one region to another (a typical dredging equipment. Dredging takes place in shallow water areas of lakes, rivers or ocean for the purpose of land reclamation, desilting, flood prevention, creation of new ports or expansion of existing ports. Hence, various industries which utilize dredge pumps are construction industry, mining industry, coal industry and oil & gas industry.
Dredge pumps are a special category of heavy duty slurry pumps that are utilized in the process of dredging. Dredging is referred to as the process of transport of underwater sediments (usually sand, gravel or rocks) from one region to another (a typical dredging equipment. Dredging takes place in shallow water areas of lakes, rivers or ocean for the purpose of land reclamation, desilting, flood prevention, creation of new ports or expansion of existing ports. Hence, various industries which utilize dredge pumps are construction industry, mining industry, coal industry and oil & gas industry.
Primary selection requirements for dredge pumps
Apart
from economic considerations, two primary selection considerations for
dredge pump operation are no settlement of sediments in the pump and
minimum amount of wear and tear in the pump due to the flow operation.
The key design parameters to keep in mind to satisfy the primary
requirements are the type of installation, critical flow rate, total
discharge head, and the pump design material.
Know your slurry type:
Before moving on to estimating the design parameters of ‘your’ slurry pump, an extremely crucial step is being familiar with the material that needs to be transported. Therefore, estimation of pH and temperature of the slurry, the specific gravity of slurry and concentration of solids in the slurry is the first crucial step towards the direction of ‘your’ ideal pump selection.
Critical flow rate estimation:
Critical flow rate is the transition flow rate between a laminar and a turbulent flow and is calculated based on grain diameter (size of slurry particles), the concentration of solids in the slurry and the pipe diameter. For minimal settlement of sediments, the actual pump flow rate of ‘your’ pump should be higher than the calculated critical flow rate for your application. However, it is important to be careful with the selection of the pump flow rate as the increase in flow rate will increase the wear and tear or abrasion of the pump material and hence reduce the lifetime of the pump. Hence, for an uninterrupted performance and extended lifetime, the pump flow rate should be optimized.
Discharge head estimation:
Total discharge head is a combination of static head (actual elevation difference between the surface of the slurry source and the discharge) and friction loss in the pump. Along with dependence on the geometry of the pump (pipe length, valves or bends), friction loss is also affected by the pipe roughness, flow rate and slurry concentration (or percentage of solids in the mixture). The friction losses increase with the increase in pipe length, the specific gravity of the slurry, concentration of the slurry or the slurry flow rate. The pump selection procedure requires that discharge head of ‘your’ pump is higher than the calculated total discharge head. On the other hand, it is crucial to note that the discharge head should be kept as low as possible to reduce the pump abrasion due to slurry flow.
Before moving on to estimating the design parameters of ‘your’ slurry pump, an extremely crucial step is being familiar with the material that needs to be transported. Therefore, estimation of pH and temperature of the slurry, the specific gravity of slurry and concentration of solids in the slurry is the first crucial step towards the direction of ‘your’ ideal pump selection.
Critical flow rate estimation:
Critical flow rate is the transition flow rate between a laminar and a turbulent flow and is calculated based on grain diameter (size of slurry particles), the concentration of solids in the slurry and the pipe diameter. For minimal settlement of sediments, the actual pump flow rate of ‘your’ pump should be higher than the calculated critical flow rate for your application. However, it is important to be careful with the selection of the pump flow rate as the increase in flow rate will increase the wear and tear or abrasion of the pump material and hence reduce the lifetime of the pump. Hence, for an uninterrupted performance and extended lifetime, the pump flow rate should be optimized.
Discharge head estimation:
Total discharge head is a combination of static head (actual elevation difference between the surface of the slurry source and the discharge) and friction loss in the pump. Along with dependence on the geometry of the pump (pipe length, valves or bends), friction loss is also affected by the pipe roughness, flow rate and slurry concentration (or percentage of solids in the mixture). The friction losses increase with the increase in pipe length, the specific gravity of the slurry, concentration of the slurry or the slurry flow rate. The pump selection procedure requires that discharge head of ‘your’ pump is higher than the calculated total discharge head. On the other hand, it is crucial to note that the discharge head should be kept as low as possible to reduce the pump abrasion due to slurry flow.
Pro Tip - How to Choose a Pump Essential Questions
1.What type of material will be pumped? (sand, mud, coarser particles, sludge, etc)
2.Flow rate target goals? (__m3/h, e.g.)
3.Length of pipeline? (__meters, e.g.)
4.Elevation rise of pipeline? (___meters, e.g.)
5.Type of pipeline? (plastic, metal, e.g.)
6.What is the density of the material?
7.What is the viscosity of the material?
What you should know about your project. These items are important in determining the proper Tobee Pump for your project. Hopefully, any company you get a quote from is asking these questions. This is especially important in the pumping of sludge, slurry, muck, mud and other viscous materials.
1.What type of material will be pumped? (sand, mud, coarser particles, sludge, etc)
2.Flow rate target goals? (__m3/h, e.g.)
3.Length of pipeline? (__meters, e.g.)
4.Elevation rise of pipeline? (___meters, e.g.)
5.Type of pipeline? (plastic, metal, e.g.)
6.What is the density of the material?
7.What is the viscosity of the material?
What you should know about your project. These items are important in determining the proper Tobee Pump for your project. Hopefully, any company you get a quote from is asking these questions. This is especially important in the pumping of sludge, slurry, muck, mud and other viscous materials.
Pump power rating:
The power consumption by the dredge pump is estimated from the discharge head, flow rate and specific gravity of pumped slurry. It is critical to verify that power rating of the selected pump is higher than the calculated power consumption after taking into account reasonable variations in operating conditions.
Material selection:
Typical material used for the construction of slurry pumps are cast iron, stainless steel, and high chrome steel. Some slurry pumps come with a lining to better deal with problems of slurry abrasion. A few elastomers which are used in the lining material are natural rubber, polyurethane or neoprene. The selection of lining material depends on the operating temperature, pH of slurry and the presence of specific abrasive fluids used in the dredging process.
Type of slurry pump installation:
Based on the shaft orientation, the slurry pumps can be divided as horizontal pumps and vertical pumps with horizontal pumps having the shaft in a horizontal position while the vertical pumps have a vertically aligned shaft.
Horizontal pumps are the most common types of slurry pumps used, and hence have the advantage of ease of installation or maintenance, a wide range of selection of flow parameters and choice of design materials. However, the vertical pumps among other benefits have the advantage of requiring relatively much lesser ground space for installation.
Another method to classify the type of installation for slurry pumps is dry installation or wet installation. Dry installation pumps have the hydraulic end and the drive located outside the liquid while the wet installation pumps such as submersible pumps operate inside the sump or the slurry. The submersible pumps do not require much support structure, hence, do not occupy much space. Depending on the kind of operation and installation desired the preferred method of pump installation is decided.
Specific problems faced in Dredge pump operation
Clogging:
Due to an extremely varied grain size distribution of materials handled by dredge pumps clogging of the suction or discharge of the pumps is a damaging phenomenon which leads to expensive maintenance procedures and more importantly high downtime. Our patented technology at Tobee pump has a high tolerance of sizes of materials handled, with a capacity to handle sizes as large as 9 inches. The open rotor design lets anything which can go through the inlet pass through the discharge without any setbacks.
Abrasion:
Massively abrasive nature of slurry’s solid particles causes an enormous amount of wear and tear in pumps. Due to the harsh environments in which slurry pumps operate, Tobee pump gives utmost importance to use the finest material for the impeller, seal, and casing to prolong the lifetime of the pump.
Conclusion:
Hopefully, you have a better understanding of the elements needed for proper pump selection. Even better is talking with us to help with your project specific needs.
At Tobee Pump we are committed to providing best-in-class dredge pumps to our customers; hence, each component is thoroughly tested to deliver supreme quality, reliability and versatility. Our unique technology provides us with an extraordinary capability to easily handle materials with enormous volumes and high specific gravity in tough conditions.
HEBEI TOBEE PUMP CO.,LIMITED
Add:Hi-tech Development Zone | Shijiazhuang City | Hebei Province | China.
Email:Sales@tobeepump.com | Skype:Tobee.pump | Mob:+86-18032034573 | Web:www.tobeepump.com
评论
发表评论